Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Cost in Malden?
Most garage door work in Malden runs $150 to $600, depending on the part that failed. A single broken spring is typically $180 to $340, cable and roller jobs sit lower, and a full new door installation lands between $700 and $2,200. We give free estimates so you know the number before anyone touches the door, and the written estimate is what sets the final price.
Malden has a lot of older two- and three-family homes with detached or under-house garages, plus newer construction around Oak Grove and the downtown blocks near the Malden Center T stop. Those older garages carry doors and openers that have been cycling for decades, which is why spring and opener repairs are the most common calls we get in this city. If your door won’t open, the range above tells you what to expect. Call (844) 542-3157. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- A single spring replacement is typically $180 to $340 in Malden; a matched pair is usually replaced together and costs about twice that.
- New door installation runs about $700 to $2,200, with door size, material and insulation driving most of the spread.
- We work on LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor equipment, so there’s no guesswork on your opener.
- Estimates are free, and same-day service is available for doors that leave a garage open and exposed.
- Our technicians have up to 11 years of experience, and our local pros are licensed and insured as Massachusetts requires.
Garage Door Cost Breakdown (2026)
Here’s what the main jobs run in Malden this year. Every figure is a typical estimated range for the work described, not a quote. Your written estimate is the price.
| Service | Typical Estimated Range in Malden |
|---|---|
| Garage door repair (general) | $150 – $600 |
| Spring repair (one spring) | $180 – $340 |
| Cable repair | $130 – $250 |
| Opener repair | $120 – $320 |
| Opener installation | $250 – $550 |
| Panel replacement | $250 – $500 |
| Track realignment | $120 – $240 |
| Roller replacement | $110 – $220 |
| New door installation | $700 – $2,200 |
Two things push a job toward the top of a range. The first is a pair of springs instead of one: because both springs in a matched pair have cycled the same number of times, they’re usually replaced together, so a pair lands around $360 to $680. The second is door size and material. A single-car steel door is one thing; a double-wide insulated door with windows and decorative hardware is another, and the price tracks the materials and the hours. Low end of the ranges above is a straight parts swap on a standard door. High end is heavier hardware, rusted fasteners, a bent section that needs realignment before anything else can be done, or a door that has to come down and go back up.
What Affects Garage Door Pricing in Malden
Pricing isn’t random. These are the factors that move a Malden job up or down:
- Age of the garage and hardware. Much of Malden’s housing stock is a century old, and garages built with that housing often have original or replacement hardware that has been patched together over the years. Seized bolts and mismatched parts add time, and time is the biggest variable in any repair.
- Weather and seasonal cycling. New England winters bring freeze-thaw cycles and road salt tracked into the garage, and a steel door with a frozen bottom seal or a binding track strains the opener every time it runs. Spring, after a hard winter, is when we see the heaviest volume of cable and track calls.
- Brand and model. A repair on a LiftMaster or Genie opener is a different job from one on an older Craftsman unit, and parts availability varies by model. We’re factory-familiar with all eight major brands, which keeps a job from stalling on a wrong part.
- One spring or two. As noted above, a pair is about twice the cost of one spring, and it’s the right call whenever both have the same wear on them.
- Door type and size. Single-car versus double-car, steel versus wood-look composite, insulated versus uninsulated. Insulated panels cost more, and a heavier door may need a stronger opener or a torsion setup rather than extension springs.
- What else fails when one thing fails. A snapped cable often takes a roller or a track out with it, and a broken spring can leave a door crooked enough that the panels need realigning. We price the whole job in the estimate so there are no surprises mid-repair.
What Does a Garage Door Repair Actually Include?
A garage door repair covers whatever is keeping the door from running smoothly and safely. That’s usually a diagnosis of the whole system rather than the single part that made the noise. Our technicians check the springs, cables, rollers, hinges, tracks, panels and opener together, because a door that jumps a track almost always has a second problem behind it.
Most repairs fit into five buckets:
- Spring repair. The most dangerous job on the door. Torsion and extension springs are under extreme tension, and a failure can cause serious injury. We handle spring repair in-house rather than subcontracting it, because it’s too risky to hand to someone who only occasionally touches a garage door.
- Cable repair. Cables are the second half of the lifting system and are also under heavy tension. Frayed or snapped cables are a safety issue, not a convenience one.
- Opener repair. Motors, gears, logic boards, sensors and remotes. A lot of openers get replaced that only needed a repair, which is why we diagnose before we recommend a new unit.
- Track and roller work. Realigning bent track, replacing worn nylon rollers with quiet sealed-bearing ones, and tightening the door back onto a true path.
- Panel replacement. A dented or cracked section can usually be swapped without replacing the whole door, which saves a lot of money.
Safety note: springs and cables are the two parts of a garage door that genuinely injure people. Don’t try to release, adjust or replace them yourself. If you see a gap in a spring, a cable hanging loose or a door that drops hard, keep people clear and call a trained professional. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
How Much Does a New Garage Door Cost in Malden?
A new garage door installation in Malden typically runs $700 to $2,200. The door itself is most of the cost, and it’s where the range lives. A standard single-car steel door sits near the bottom. A double-wide insulated door with windows, a carriage-house look or a composite overlay sits near the top. Opener replacement adds $250 to $550 if your current unit won’t lift the new door.
It’s worth knowing when to repair and when to replace. A panel dent or a single failed component almost always favors repair. A door with rusted-through bottom sections, a bent track that won’t true up, or hardware that keeps failing repair after repair is usually better replaced. If your door is older than your opener and both are limping, replacing both at once is often the cheaper path in the long run. Ask for a free estimate on both so you can compare the numbers side by side.
For the full list of what we handle, from emergency response through installation, see Lynn Garage Door Repair Pros. One call covers every stage of the door’s life.
Spring Repair: The Dangerous Job, Priced Honestly
Spring repair is $180 to $340 for one spring in Malden. A matched pair is usually the right call and costs about twice that, roughly $360 to $680. We don’t downplay the risk here because it’s real. A torsion spring carries enough stored force to break a bone or worse, and extension springs under a low-headroom garage door are just as dangerous when they let go.
That’s why a spring repair isn’t a job to price-shop on the lowest number. What matters is that the technician knows the winding procedure, uses the right winding bars, and replaces the spring with a matched one for your door’s weight. Our technicians have up to 11 years of experience and handle spring work in-house. If you hear the loud bang and the door won’t lift, that’s the sound of a spring letting go. Don’t force the door. Call (844) 542-3157. We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Opener Repair or Replacement: How to Decide
Opener repair runs $120 to $320, and a new opener installed runs $250 to $550. That gap tells you why diagnosis matters. A remote that won’t work, a sensor that’s misaligned after being bumped, or a gear that’s stripped are all repairs. A motor that’s burned out or a logic board that’s failed on a very old unit may be a replacement.
We work on LiftMaster, Chamberlain, Genie and Craftsman openers, plus the openers that ship with Clopay, Amarr, Wayne Dalton and Raynor doors, which covers most of what’s installed in Malden garages. No guesswork on your opener means fewer wasted service calls and a straight answer on whether repair or replacement makes sense. If your door reverses on the way down, stops halfway, or the wall button won’t respond, give us a call at (844) 542-3157 before you buy a new unit.
How to Save on Garage Door Cost in Malden
You can’t avoid a spring failing, but you can avoid paying for the wrong fix. These are the moves that keep a bill low:
- Get the diagnosis right the first time. A door that “needs a new opener” often needs a $20 sensor or a $40 gear. A free estimate that checks the whole system saves more than any discount.
- Replace both springs when both are worn. It stings to pay for a pair, but replacing one spring on a door with two, then replacing the other a few months later, costs more total than doing both at once.
- Repair panels before replacing doors. A cracked top section is a $250 to $500 repair, not a $2,200 replacement. Only replace the door when the frame or the whole assembly is compromised.
- Tighten the small stuff on a schedule. Rollers, hinges and tracks wear slowly, and a $110 to $220 roller replacement done before the track bends costs less than the track work that follows.
- Ask for a written estimate. Free, specific and itemized. Call (844) 542-3157 and we’ll give you the numbers before any work starts.
If your door failed today and the garage is standing open, same-day service is available. Call (844) 542-3157. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Choose a Single-Trade Garage Door Specialist in Malden?
A garage door is a system, and the parts talk to each other. The spring is sized to the door’s weight, the opener is sized to the door’s resistance, and the tracks have to be true for either to work. A general handyman who handles garage doors as one of a dozen services is guessing at that system. We aren’t. We handle garage door repair, opener repair, spring repair, installation and emergency service, and nothing else.
That focus shows up in small ways. We know which LiftMaster and Chamberlain openers use which travel modules. We know Clopay and Amarr panel profiles by sight. We know that a Wayne Dalton door with a broken torsion spring on a Malden triple-decker’s under-house garage needs to be wound on the correct side for the low headroom. Those specifics come from doing one job over and over, not from a generalist trying a new thing.
If you want to see how we handle each kind of job, the service pages cover garage door repair, garage door opener repair, garage door spring repair and garage door installation in detail. If the door has already failed and the garage is open to the street, which happens in every neighborhood from Maplewood to Edgeworth, our emergency garage door service is the right call.
Frequently Asked Questions About Garage Door Cost in Malden
How much does garage door repair cost in Malden?
Garage door repair in Malden typically runs $150 to $600, depending on the part. A single spring is $180 to $340, cable repair is $130 to $250, and opener repair is $120 to $320. Call (844) 542-3157 for a free estimate. The written number is the price.
Is it cheaper to repair or replace a garage door?
Repair is almost always cheaper unless the door itself is compromised. A panel replacement is $250 to $500, and a full new door installation is $700 to $2,200. Replace when the frame, hardware and panels are all failing at once; repair everything else. Call (844) 542-3157 and we’ll price both options side by side.
Why does a pair of springs cost more than one?
A pair costs about twice the single-spring range, roughly $360 to $680, because a matched pair is usually replaced together. Both springs have cycled the same number of times, and replacing one while the other is near failure just moves the cost down the road. Call (844) 542-3157 for a free estimate on your door.
Can you come out today?
Yes, same-day service is available for doors that have failed and left the garage exposed. The sooner you call, the sooner we can get a technician out. Call (844) 542-3157. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. If you’re calling outside those hours, we’ll book you into the next opening.
How much does a new garage door cost in Malden, MA?
New installation is typically $700 to $2,200, with door size, material and insulation driving most of the spread. A standard single-car steel door is at the low end; a double-wide insulated door with windows is at the high end. Add $250 to $550 if you also need a new opener. Call (844) 542-3157 for a free estimate.
Do you work on my brand of door or opener?
We work on LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor equipment. That covers virtually every door and opener in a Malden garage. Call (844) 542-3157 and tell us the model if you know it – we’ll confirm before we schedule.
What areas around Malden do you serve?
We serve homeowners in Malden and the surrounding communities, including Everett, Medford, Melrose, Saugus and Stoneham. If you’re nearby and not sure whether we cover your street, call (844) 542-3157 and ask.
Other Garage Door Guides
If you’re weighing a repair against a replacement, our guides on garage door spring repair cost and garage door opener repair cost break down the line items. If a new door is in your future, garage door installation cost walks through door styles and options. And if your door is making noise, garage door noise repair explains what each sound usually means.
Get a Free Garage Door Estimate in Malden
Pricing in Malden is genuinely knowable. A single spring runs $180 to $340, most repairs fall between $150 and $600, and a full installation is $700 to $2,200. What isn’t knowable until we look is which of those you’re facing. Call (844) 542-3157 for a free estimate, and we’ll tell you straight. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. If the door is open and the garage isn’t secure, say so when you call and we’ll treat it as urgent. Our local pros are licensed and insured as Massachusetts requires, our technicians have up to 11 years of experience, and we work on the eight major brands – LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman and Raynor – so there’s no guesswork on your equipment.
Pricing reflects the Malden market as of 2026. Lynn Garage Door Repair Pros offers free estimates – call (844) 542-3157.
What Our Customers Say
"Opener kept reversing halfway down. Turned out to be the safety sensors knocked out of alignment by a bicycle. He straightened them, wouldn't charge me for it, and just asked me to keep them in mind if I need real work later."
- Jessica Nguyen"Replaced the bottom panel after I backed into it. Color match is close enough that you have to know to look for it."
- Dale Schaefer"Both cables had come off the drum and the door was hanging crooked. I'd watched a video and was about ten minutes from trying it myself, which the tech told me would have been a genuinely bad idea. Glad I called."
- Nicole Miller